BrewForge Docs

Step Mash Calculator

Step mash planner: strike water for the mash-in, then the boiling water to add (infusion), the thick mash to pull (decoction) or direct heat for every rest, with Hochkurz and decoction templates.

The Step mash calculator plans a mash with several rests. You list your rests; it tells you the strike water for the first one and, for every further rest, how much hot water to add or how much thick mash to pull for a decoction.

The step mash calculator with its default Hochkurz plan: mash in with 15.0 L at 68.7 °C for 63 °C, then add 5.5 L and 6.1 L at 100 °C for 72 °C and 78 °C; 26.6 L total mash water, 5.32 L/kg final thickness, 80 min rest time

Open it with Calculators in the sidebar → Step mash. It starts with the Hochkurz rests and remembers your last plan in this browser. On a phone the strike water stays pinned at the bottom of the screen while you edit.

Grain and water

FieldWhat to enter
UnitsThe button in the section bar. Temperature in °C or °F, Volume and weight in L, kg or gal, lb. It starts in your units from Settings; switching converts the values you entered.
Grain weight and Grain temperatureThe whole grain bill; grain temperature is usually room temperature.
Mash-in water asRatio (Water-to-grain ratio in L/kg or qt/lb) or Volume (Mash-in water). The hint below the field shows the other value (= 15.0 L). Switching converts the value.
Hot waterA closed fold with the infusion water temperature next to its title. Open it to change the Hot water temperature: boiling (100 °C / 212 °F), or lower at altitude.

Rests

The Rests section bar shows how many rests you have and their total time (3 · 80 min). The list shows each rest with its number, how it's reached, temperature and time. The first rest is always the mash-in; add the rests in the order you do them.

  • Add rest adds a rest a few degrees above the last one (up to 78 °C). A plan holds up to 12 rests.
  • Click a rest to edit it.
  • The ⋯ menu → Fill from a template replaces the list with a starting point: Single infusion (67 / 78 °C), Hochkurz (63 / 72 / 78 °C), Protein rest (52 / 67 / 78 °C) or Double decoction (52 °C, then 64 and 72 °C by decoction).

Without rests the plan asks you to add a rest or pick a template.

Edit a rest

The dialog Rest 1, Rest 2 … says where the rest sits in the plan ("Step mash · after mash-in at 63 °C") and has these fields:

  • Temperature and Time (min). The time is optional and only summed up.
  • Reached by (not for the first rest, which is the mash-in): Hot water, Decoction or Direct heat.

Below the fields you already see what this rest needs ("Add 5.5 L at 100 °C") and any warning for it. Save closes the dialog, Save & add another saves and opens the next new rest, Remove deletes the rest, Cancel discards your changes.

Your plan

The answer on the right starts with the Strike water for the mash-in ("15.0 L at 68.7 °C"). Below it, one line per rest, titled with how it's reached and its temperature ("Hot water · 72 °C"), with the time on the right:

  • Mash-in: "Mash in with 15.0 L at 68.7 °C".
  • Hot water: the water to add, "Add 5.5 L at 100 °C".
  • Decoction: "Pull 4.8 L thick mash, boil it, stir it back in". The mash water stays the same.
  • Direct heat: "Heat to 72 °C", or Nothing to add, keep resting when the temperature doesn't change.
  • Under each step: the mash water and its thickness after the step ("Mash water 20.5 L · 4.09 L/kg").

Totals follow: Total mash water, Hot water after mash-in, Final thickness and Total rest time.

Warnings tell you:

  • when a rest can't be reached with your hot water (heat it directly or use a decoction) or with a decoction (heat it directly),
  • when a rest is cooler than the one before it,
  • when the strike water would have to be hotter than boiling (mash in with more water or at a lower rest),
  • when the mash gets thinner than 6 L/kg (2.9 qt/lb): start thicker, or heat the later rests directly or with a decoction.

How it's calculated below the totals sums up the assumptions.

How BrewForge calculates each step

Mash-in: the strike water formula with a preheated tun: T_strike = T_rest + 0.4 / R × (T_rest − T_grain).

Hot water infusion (W water in the mash in liters, G grain in kg, T_water hot water temperature):

V_add = (T_new − T_now) × (W + 0.4 × G) / (T_water − T_new)

Decoction, returned at 98 °C, no evaporation: the heat needed is V_thermal = (T_new − T_now) × (W + 0.4 × G) / (98 − T_now). Thick mash also holds the grain's own volume (0.67 L per kg), so the volume to pull is V_thermal × (W + 0.67 × G) / (W + 0.4 × G). A decoction is flagged as not reachable when V_thermal would be the whole mash (W + 0.4 × G) or more.

Direct heat: nothing is added. Heat lost during the rests isn't included, so check the temperature and add the water slowly while stirring.

Example (default Hochkurz, 5 kg grain at 20 °C, 3 L/kg): mash in with 15 L at 63 + 0.4 / 3 × 43 = 68.7 °C. For 72 °C add 9 × (15 + 2) / 28 = 5.5 L of boiling water, for 78 °C another 6 × (20.5 + 2) / 22 = 6.1 L. Total 26.6 L, final thickness 26.6 / 5 = 5.32 L/kg.

Example (Double decoction template, same grain): mash in with 15 L at 52 + 0.4 / 3 × 32 = 56.3 °C. For 64 °C: 12 × 17 / 46 = 4.43 L thermal, × 18.35 / 17 = 4.8 L of thick mash to pull. For 72 °C: 8 × 17 / 34 = 4.0 L thermal, × 18.35 / 17 = 4.3 L.

On this page