BrewForge Docs

Hop stand curves

Model how your wort cools after flameout with a hop stand curve in BrewForge, described in brewing terms or as measured points, for more accurate whirlpool and hop stand IBU. Includes the temperature factor and integration formula.

After flameout the wort keeps isomerizing alpha acids, but more slowly the cooler it gets. A flat hop stand (one temperature for a fixed time) is a rough estimate. A hop stand curve describes how your wort actually cools, for example from 95 °C to 80 °C in 20 minutes and further down while chilling, so BrewForge can calculate whirlpool and hop stand IBU minute by minute.

Equipment profiles and recipes can use a hop stand curve instead of the flat hop stand temperature and duration (see Use a curve).

Create a curve

Hop stand curves belong to the kettle, so they are listed on the Equipment tab of Settings → Profiles, below your equipment. Click New curve in the Hop stand curves section, or New curve in the hop stand part of an equipment profile's Kettle dialog. There are no curve templates, and curves have no default: an equipment profile selects one or uses the flat hop stand.

A hop stand curve with its chart, the points and the equipment that uses it

The curve page shows the chart, the Points (minutes and temperature) and Used by, the equipment profiles that use this curve. Click Edit to change it:

The Hop stand curve dialog with five measured points

Under Enter as you choose how to describe the curve:

  • Describe it: in brewing terms. The wort is At flameout at one temperature, Cools to a second temperature After some minutes, and is optionally Then chilled (Add chilling): Chilled to a final temperature Within some minutes. BrewForge turns this into two or three points. A new curve starts at 95 °C, cooling to 65 °C after 30 minutes.
  • Points: for a measured curve. Each point has minutes and a temperature; between two points BrewForge assumes a straight line. Add point adds a point 10 minutes after the last one and 10 degrees cooler (not below 20 °C). A curve with more than three points can only be edited as points.

A curve needs at least two points, the first one at 0 min (flameout), and each point after the one before. Times go up to 240 minutes, temperatures up to 100 °C.

To measure your curve, take the kettle temperature at flameout and then every few minutes during the whirlpool and chilling, the way you normally brew.

Use a curve

Open your equipment profile, edit the Kettle, choose Cools along a curve under Hop stand and pick the Curve. Brews then calculate whirlpool and hop stand IBU along that curve instead of the flat Temperature and Duration. With Holds one temperature the flat settings are used, so there is no default curve.

  • The curve is copied into a brew together with the rest of the equipment profile: when you create a brew with your default equipment profile or apply the equipment profile to a brew. Brews created before you selected the curve keep the flat hop stand until you apply the profile to them again.
  • A hop stand curve set on an individual recipe takes priority over the curve from the equipment profile.

How BrewForge uses the curve

Temperature factor

Isomerization slows down with temperature. BrewForge uses a relative utilization from the mIBU model:

factor = 2.39 × 10¹¹ × e^(−9773 / (T + 273.15)), with T in °C, limited to 0–1.

Examples: 100 °C → 1.0, 95 °C → 0.71, 90 °C → 0.49, 85 °C → 0.34, 80 °C → 0.23, 70 °C → 0.10, 60 °C → 0.04.

Hopstand IBU along a curve

BrewForge steps through the curve one minute at a time. For each minute it takes the curve temperature at the middle of that minute (linear between your points) and adds:

IBU += alpha acid (as decimal) × hop amount (mg/L) × (U(t + 1) − U(t)) × factor(T) × hop utilization

U(t) = 1.65 × 0.000125^(gravity − 1) × (1 − e^(−0.04 × t)) / 4.15 is the Tinseth utilization, hop amount (mg/L) = grams × 1000 / batch volume in liters, and hop utilization is the setting from the equipment profile.

For whirlpool additions t starts at 0. Boil additions continue from their boil time, so a 60-minute addition only gains a little during the hopstand. A hop with its own temperature uses that temperature for the whole curve instead.

Example: 50 g of 10 % hops in 23 L at 1.050, whirlpool only. Flat at 80 °C for 20 minutes gives about 7.0 IBU. A curve falling linearly from 95 °C to 75 °C over the same 20 minutes gives about 12.3 IBU, because the first minutes are much hotter.

The flat model uses the same formula with one temperature for the whole duration: IBU = alpha acid × mg/L × (U(start + duration) − U(start)) × factor(T) × hop utilization.

On this page